- Comparing cyclones - need help
- 3-phase
- Actual Motor Size
- Current Draw
- Clear Vue Performance
- Current Draw
- minimum particle size
- Another advantage of clearvue
- Motor Problem
- Advice on DC placement
- Advice LH instead of RH
- Wiring the coil and remote start feature
- Trash can Stress Cracks
- CV 1800 footprint?
- Shop Vac Cyclone - Efficiency
- Breaker Size
- Hello & Clear Vue Comparison & Questions
- Current draw on my LH CV1800
- Connecting to intake chute?
- CV06 Central Vac Idea
- Turning cyclone on and off
- Remote control relay
- A sad day in the shop, dead motor
- Mini cyclone blower/vacuum options
- shop vac cyclone
- Height Restricted - Remote blower
- Problems with Clearvue Mini set up
- Dust receptacle (trashcan) shape. Does it have to be round?
- New mini-cyclone setup.....
- Installing my CV1800
- Mini CV06 discharge @ 90 degrees?
- Mini CV 06 is coming apart
- Crazy Awesome Customer Service
- Mini for contractor table saw
- Clearvue Customer Service
- What size shop vac for the mini cyclone
- Outstanding Customer Service
- Mini and MDF?
- Plastic bags in garbage can
- Maximum Hose Length With a Mini?
- Beginner Questions
- what size cyclone?
- CV06 Height and Noise Increase?
- Question on blast gates
- collection bin overflow damage impellor ?
- Is this too far to run piping ?
- Can I dogleg the pipe to the collection bin ?
- Exhaust from filters
- Switched circuit and plug instead of 110v relay and direct wire?
- How do you handle cans full of dust?
- How tall is the mini?
- Tightening the taperlock bolts
- Mini CV06 & tough dust
- Model 1660 for Mini Conversion Lid
- 55 Gallon Drum Collection guide
- How to size the breaker for Leeson 20.8a motor
- retro fit older motor/vacuum (5HP)
- capacity
- Questions from a newbie
- For Sale
- Clear Vue vs. Oneida
- Mini CV06 - airflow requirements
- Inlet and outlet locations - adjustable, but becomes fixed at assembly?
- Rabbeted plate to blower housing
- Hello,new here with a couple questions
- Wiring two devices to the output side of the relay
- Fasco H230B relay - wiring diagram/instructions?
- Modify transition to go straight out with pipe
- How to wire motor with 4 wire cable
- Dust Bin question
- Bin overflow sensor help
- Where does the ground go on the line from the remote to the relay?
- Noisy bearings in motor
- looking for recomendation
- Behavior of Summit CP688 photocell - McRabbet
- Does the 1800 come with one or two filters?
- Mini without a shop vac?
- Fastening Transition to Blower Housing
- Question About Trash Can / Dust Bin Removal
- Sale question: Remote removed & general remote ??'s
- Important lesson learned about handling the cyclone
- Material backing up at bottom of my cyclone
- CV1800 Fired Up - Funny Story (& Questions)
- Does my cleanout need some volume in it?
- Quieter blowers?
- Cyclone done! And a question
- Newbie Relay Switch Question
- New Owner - As soon as it gets here
- Another newbie
- Product / Installation Updates
- Clearvue with smaller motor?
- PETG Fittings
- CV1400 Available?
- Left and Right explanation
- Leeson Motor Connects
- Sealing motor to shroud
- As the impeller slows to a stop.. squeaks and chirps
- CV1400 finally installed !
- Dust collection bin suggestions ?
- Top 21 tools rated by Tool Crib
- Fan ImpellarMount
- Remote signal failing
- Cyclone Ramp
- False Starts
- 5 HP Leeson
- Odd thing happened
- venting to outside
- New installation - problems
- Vertical lift of CW1800 & basement install
- Painting MDF?
- Construction question
- Blower Vac Conversion Lid
- post in blower housing - Pupose?
- Issues with motor mount and impeller
- Electrical Question
- Cyclone inlet chute angle??
- Inlet tube position vs. impeller - experiment?
- Exhaust to open air or not?
- Interference with enclosure and plywood
- Inverter buying info. for UK
- Possible source for 55 US gal steel dust bins....
- Mini cyclone
- How concerned should I be about Clearvue impeller coming loose?
- If anyone buys this company
- Next best cyclone available?
- Clear Vue IPO
- Welcome Back